Alure Home Improvements Instructs How To Caulk Your Exterior Doors And Windows

first_imgSign up for our COVID-19 newsletter to stay up-to-date on the latest coronavirus news throughout New York Sponsored Content Brought To You By Alure Home ImprovementsWhether it’s air-conditioning or heating season, leaks at home can cost you energy—and that adds up to money blowing in the wind. An estimated 65 percent of a homeowner’s utility bill is used to heat or cool the indoors. Don’t let it go to waste. Weatherization is the solution. That means examining your outside doors and windows for cracks around the frames and filling them in with caulk. You might also want to check your attics, basements or crawl spaces for any gaps because they too can be a problem.Thanks to this recent installment of the “60 Second Fix: How To Caulk An Exterior Door In 60 Seconds,” featuring Alure Home Improvement’s chief operating officer Doug Cornwell, you’ll learn the simple steps required to get the most of your caulking experience. Since you’re doing the exterior of your house, you want to make sure that you select the right caulk so it will withstand any kind of weather. Silicone, not acrylic, caulking is preferred, because it is permanently waterproof, flexible, and shrink- or crack-proof. Remember, caulk is not an adhesive—it won’t bond wood together, or tiles to a wall or a floor. And here’s something else to consider: If the crack is wider than half an inch, you might have to get a foam rod that you can wedge into place before you caulk.So, once you have the proper caulk, you’ll need the caulk gun to squeeze it out of the tube properly. Don’t leave the hardware store without it.Preparation is also important. You don’t just apply new caulk on top of old caulk. It won’t work effectively. Use a razor blade or a sharp knife to remove the old caulk first so you remove any mold or mildew that might have collected on the surface. Next, clean the crack with a rag dampened with a household cleaner or rubbing alcohol, or a wire brush. Then wipe the area with a clean cloth because you want to make sure that the surface is clean, dry and free of grease, dirt and dust before you begin to caulk.Okay, now you’re ready to caulk, and this is where Cornwell comes in with his expertise to improve your technique.“When you’re opening a tube of caulking,” Cornwell says, “you want to make the smallest hole possible at the end of the tip.”As Cornwell puts it:  “Less is more.” How wide a hole you need depends on the width of the crack, of course. But a professional-looking bead, which is what a line of caulk is called, begins with the properly sized opening. A cut near the tip produces a thin bead, a cut further down the nozzle yields a thick bead.Next, you’ll have to break an inner seal on the silicone tube before you insert the tube into the caulk gun. Take a stiff metal wire or a similar-sized object like a nail and poke it through the tip until you feel it break the seal. Many caulk guns come with just the right sharp tool for this function. Cornwell shows how it’s normally folded along the gun when it’s not needed.And there’s a thin rod that’s part of the caulking gun about the size of a 10-penny nail [?] and insert that through the tip to free the passageway, to make sure the caulk can travel freely… from the tube to the tip…Once you’re sure the caulk will flow freely, insert the tube of caulking into the gun and squeeze the trigger a couple of times so the small metal plate attached to the rod advances into the flat bottom of the tube and begins to exert pressure.“Make sure it’s snug and ready to go,” Cornwell says. You should be able to see the caulk fill the tip and be ready to emerge.Caulking novices might want to practice on cardboard first, but not Doug Cornwell, he’s an old pro, and he goes right to work.“One thing you want to keep in mind when you’re caulking, whether you’re caulking a door, a window, or even a wine bottle, you want to keep constant, even pressure,” he advises.“As hard as you squeeze is as fast as you want to move,” Cornwell says. “If you want to squeeze very hard, you have to move very fast. It’s got to be tempo: tempo, tempo, tempo!”For a doorway or window frame, he says, “You always start at the top corner and work your way down.”Hold the caulk gun at a 45-degree angle and press the tip right into the corner. Then start squeezing the trigger as you slide the tip downward, making sure the flow produces a nice, constant bead of caulk.Steady as it goes is the key. Watch Cornwell as he keeps the pressure even, and the caulk flowing out smoothly. He follows along, bending when necessary to maintain the proper angle.Click here to learn more about Alure Home ImprovementsNext comes what the experts call “tooling,” which means smoothing the bead. This step is just as vital to the task and should not be skipped. Cornwell recommends taking a paper towel, dampening it with a little bit of water. Then moisten your fingertip, which turns out to be the perfect “tooling” device here, and run your finger very lightly over the bead.“Go over the caulk to make sure it bridges both surfaces and the crack is filled,” Cornwell says.When you’re confident the crack is “caulked,” then use the damp paper towel to wipe the excess residue off your finger.And there you have it.last_img read more

Wizards fire team president Ernie Grunfeld after 16 seasons

first_img Lakers’ LeBron James addresses being shut down, explains offseason motivation 2019 NBA Draft lottery: Knicks, Suns, Cavs close in on best odds for top pick A disappointing season has led to a change at the top for the Wizards as Washington announced Tuesday it has fired team president Ernie Grunfeld.“We did not meet our stated goals of qualifying for the playoffs this season and, despite playing with injuries to several key players, we have a culture of accountability and a responsibility of managing to positive outcomes,” Ted Leonsis, chairman and CEO of Monumental Sports & Entertainment, said in a statement.  “I wish to thank Ernie for his service to the Washington Wizards. He and his family have been great leaders in our community and have worked tirelessly to make us a top NBA franchise.” Grunfeld was hired before 2003-04 and led Washington to a 568-724 record over the last 16 seasons with eight playoff appearances, though the Wizards never advanced past the conference semifinals.Grunfeld was given an extension in May 2017 before the Wizards finished eighth in the Eastern Conference and lost in the first round of the playoffs in 2017-18. Related Newscenter_img After that season, Leonsis wrote a letter to fans and noted “the team’s inconsistency was sometimes frustrating to watch.”“There’s no easy way to talk about a first-round loss. I’m disappointed, the team is disappointed and I know you, our fans, are disappointed,” Leonsis wrote. “Our singular goal in everything we do is to win a championship. You deserve it. Our city deserves it. It remains our first and only priority and I think our team showed this year that we have the pieces to make it happen.”  However, with a roster void of meaningful contributors beyond All-Star Bradley Beal, Washington is currently 32-46 and in 11th place in the Eastern Conference.Midseason acquisitions Jabari Parker (15.5 points per game) and Bobby Portis (14.3), are second and third, respectively, in scoring behind Beal, while highly compensated point guard John Wall only played 32 games before being shut down for the season in January with a heel injury.Senior VP of basketball operations Tommy Sheppard will take over Grunfeld’s duties and report to Leonsis as the team searches for a new president.last_img read more